Steering 6 Components Measuring Device
OSC92OT205
Device to measure steering angle while driving and 6 components applied to steering wheel. Possible to equip a
detector to steering without modifying the steering shaft. Signal of the 6 component is amplified by the highly stabled
amplifier and converted to digital via A/D converter and transmitted through slip ring for hone. Slip ring for hone
supplies power to detector from external battery and at the same time transmitthe signal of the above. Further,
computation device coverts rotational coordinate to state coordinate and provides automatic balance adjusting function.Features
1. Measurement of 6 components on steering and steering angle by 1 detector is possible.2. Possible to output of state coordinate after converted from rotational coordinate. (Pat.)
3. Measured signal is transmitted through slip ring for hone equipped to the vehicle. (Pat.)
4. Possible to replace with various detectors for steering.
| Type | Rated load | |||||
| (N) | (N) | (N) | (Nm) | (Nm) | (Nm) | |
| Fx | Fy | Fz | Mx | My | Mz | |
| -250N | +/-250 | +/-250 | +/-250 | +/-50 | +/-50 | +/-50 |
| Tire Attitude Angle Measuring Apparatus OSC 92OT205 | ||||||
| Rated output | Approx. 0.5 mV/V | |||||
| (approx,. 1000 x 10-6 strain) * | ||||||
| Non linearity | +/-0.5% FS * | |||||
| Hyteresis | +/-0.5% FS * | |||||
| Tolerable over load | +/-150% FS * | |||||
| Interference | between respective components | |||||
| +/-2%FS/FS (on output after computation) | ||||||
| Temperature influence | at zero point: +/-0.01% FS/deg.C* | |||||
| of sensitivity: +/-0.03% Reading/deg.C* | ||||||
| Built-in preammplifier | 200 times (for 6 ch) | |||||
| Rotational angle | endless | |||||
| Steering angle detector | 3600 pulse/360 deg. | |||||
| high resolution 0.01 deg. | ||||||
| A/D Converter | 16 Bit | |||||
| Gauge voltage | DC10V | |||||
| Voltage of power source | DC12V+/-2V | |||||
| Weight | less than 5 kg | |||||
| Computation amplifier OSC 92OT205A | ||||
| AUTO BALANCE function* | Steering wheel: more than approx 1 rotation | |||
| Zero point retaining time: approx. 10 days | ||||
| ZERO function (state coordinate) | Output voltage :+/-5V manual adjustment possible | |||
| RANGE function (state coordinate) | F; 250, 100, 50, 25N, M; 50, 20, 10, 5 N-m | |||
| CAL function | OFF, 1, 2, 10V | |||
| FILTER function | 1, 10Hz, PASS (50Hz) switching | |||
| MONITOR display/output | Switches signal output and angle signal before and after computation | |||
| to display on the monitor. At the same time, outputs to single connector | ||||
| Rated output | 6 components output voltage +/-10V/FS (for each component) | |||
| Steering angle output voltage | Angle range +/-45 deg/+/-10V, +/-180 deg/+/-10V, +/-720 deg/+/-10V | |||
| Digital display | 10,000V/DC | |||
| Computation accuracy | +/-1%FS | |||
| Working temperature range | 0 to 50deg.C | |||
| Voltage of power source | DC12V+/-2V (power source of common battery with detector) | |||
| External Dimensions | Approx. D400 x W430 x H149mm | |||
pdf brochure